• November 22, 2019, 06:54:57 AM
• Welcome, Guest. Please login or register.

The Future of this Forum:

The Inkscape Project opened its first official forum on its website this month (August 2019). https://inkscape.org/forums/ In an effort to combine all the different forums into one, this forum will no longer be accepting new members or new messages. However, it will remain open for a little while, for existing members, to have access to their contents, if they need them.

Any potential new members should register on the new forum, and post their message there. There is a special board for questions about using Inkscape for cutting machines (of all kinds). (https://inkscape.org/forums/cutplot/)

If you have any questions or comments (and you're an existing member) you can post them here.

Although I've been planning to put this forum in read-only mode, at the time of this transition, unfortunately, my personal circumstances have changed, and I won't be able to host this forum much longer. I'm not sure about the time frame. It could be as soon as the end of 2019, or as long as a year from now. If anyone is interested in taking it over, please contact me.

-- brynn


Author Topic: Ideas for using Extrude  (Read 3019 times)

0 Members and 1 Guest are viewing this topic.

Offline Aussie Carolyn

  • Original Member
  • *****
  • Posts: 1,025
  • Country: au
  • Gender: Female
    • Cut Two Pieces
Ideas for using Extrude
« on: May 18, 2012, 08:48:31 AM »
An easy tutorial showing the basic steps to create projects using extrude. I will leave it up to you to experiment and see what type of designs you can create.

extrude.JPG
*extrude.JPG
(36.49 kB . 728x245)
(viewed 589 times)


A few ideas for you to try
- if the shape is symmetrical flip it horizontal or vertical. It will look the same but the extrude result will be different.
- try more than two shape
- place shapes side by side and even use the same size shapes.
Give it a try and you may be surprised at the designs you can create in a few minutes.

extrude1.JPG
*extrude1.JPG
(44.62 kB . 569x285)
(viewed 597 times)


extrude2.JPG
*extrude2.JPG
(36.49 kB . 490x259)
(viewed 615 times)


extrude3.JPG
*extrude3.JPG
(31.42 kB . 483x174)
(viewed 507 times)


extrude4.JPG
*extrude4.JPG
(59.19 kB . 594x478)
(viewed 597 times)


Do not repost this tutorial on any other website or claim the written instructions as your own.
« Last Edit: September 01, 2015, 01:13:43 PM by brynn »

Offline PapaSue

  • Original Member
  • *****
  • Posts: 571
    • http://creationsbypapasue.blogspot.com
Re: Ideas for using Extrude
« Reply #1 on: May 18, 2012, 10:02:29 AM »
I'm on it.  I'll post what I've done so far in the "altered" categor as, per usual, I did it with a twist.  Just can't leave good enough alone.
« Last Edit: December 31, 1969, 05:00:00 PM by Guest »
Susan
http://creationsbypapasue.blogspot.com/
OLDER:  http://papasuecreative.blogspot.com (blog deleted)
Learn, Grow, Create, Share
Macintosh, Mavericks, Inkscape 0.91, eClips1, eCAL2.013

Offline scud

  • Original Member
  • *****
  • Posts: 154
Re: Ideas for using Extrude
« Reply #2 on: May 18, 2012, 06:02:09 PM »
Thanks Carolyn. I've saved it and one day will have a go.
Barbara
« Last Edit: December 31, 1969, 05:00:00 PM by Guest »